Search results

Have a bnr autocal with both cables for sale. $140 shipped. Pm or text 603-765-7363

Is it really just rtv/silicone used to seal this? No gasket? Been trying to find the gasket but every time it only shows rtv. I was hoping to do it today but wanted to hopefully get some clarification before I just go get rtv..

I’ve had some oil underneath the car now (leftside looking from front) all over the the oil pan and such. I have replaced my valve cover gasket (again) I changed the oil cooler seals, I did notice oil on the small lip/ring around the center of the actuator so I changed both intake and exhaust...

Does the black trim around the radio and climate controls in the rs fit in an LT? Kinda dig the black and it looks close but I know things are slightly different with the rs models.

Recently bought an autocal, went through the first steps with licensing and all that. Got my base tune, I was under the impression that once I got the base tune I was to log some data and send it back, then I would receive revisions.. unless I misunderstood how it works and I only get a base...

So I have a 13 LT sedan, I’m in the stages of tuning with jerry now. I’ve got a zzp downpipe, soon to have the midpipe, I cut my second cat out and made my own 2.5” from the (for now) stock mid pipe to a magnaflow muffler/resonator unit. My question is.. even though I’ve gotten many compliments...

I just saw a video that someone had used two bnr clamps, he did have the short shifter however I do not.. is two clamps possible with the factory shifter? I’m guessing it will tighten things up BIG time which would be great! Anyone else hear of this?

I’ve been reading what I feel like a lot today about swapping in a 2.0t but the threads seemed a little older and I didn’t really get the info I was hoping for. Has anyone ACTUALLY considered doing this? Because i am but I’d like to get a little more info. The ATS motor is what I was looking at...

So a few months ago I did the timing on my 13 LT 1.4L, I had a hell of a time getting the timing chain tensioner plug out but had finally done so. I put it back in and tightened it as firmly as I could. Well just the other day I had seen some oil on my oil pan on the left side (facing car) so I...

So I just bought these on sat/sun of last weekend. I received them today, mocked them up and they are going to work for me with what I’m doing. I could make them work but I have other plans now. It is the complete kit. I opened the box and mocked up the turbo outlet section and realized it won’t...

Yesterday driving home from work my intake temps were rising more rapidly than they used to. Typically they run anywhere from 8-12 degrees above ambient temps, yesterday with the temp around 86/87 they were upwards of 130-133 in a matter of a min or two when sitting at a light or something. Is...

Hey guys! So in about two weeks I’m pulling the trigger on a tune (finally)! Just waiting on my charge pipes to get here and then I’ll be making my decision. So here’s my hiccup, I spoke to a shop local to me here in Florida who does tuning, they use HP and i would get dyno time and all that for...

Found a billet CHRA cartriage.. is it worth it? I’ve got a stigan oem spec turbo with roughly 2500 miles on it. Nothing is wrong with it just the want for a little more if possible. Is it worth it?

I’ll be installing my new intercooler within the next week or so. My first question is, if I was to do the DDM works silicone charge pipes and use the factory 90’ section with the boost sensor would that be sufficient? I wanted to get a full 2.5” set but didn’t really want to spend the $230 on...

Selling the factory coil springs out of my sedan. Make me an offer. Will work out a shipping cost if need be.

Anyone use or attempt to use a universal intercooler like GReddy or Mishimoto? I know there are kits but wasn’t sure of the universal ones.. if so what would you guys say would be measurements? I suppose just check out the model specific kits and get a rough idea on dimensions from that? Let me...

You passed by me on 192 this morning, I have an inferno orange sedan with bronze esr sr07’s! Car looked great anyhow! Would have tried to catch up but I was running a little hotter than normal this morning so I was trying to baby her haha

Can anyone give me a little insight? I’ve done some diag on the system myself, so far I’ve checked all fuses and relays, changed out the pressure transducer switch, checked pressure on low side line. I put a meter on the fuses inside the car with switch on and both get 12.5, I did the same under...

Trying to order some AC parts and I’m not exactly an ac specialist haha, when I’m looking for certain things, there is an option for “with or w/o a thermal protection sensor/switch” .... how do I know if I have one of these or not? Please help!!

Bought these for my sedan off of eBay in May but never even opened the package they were shipped in. Changed the wheel fitment and decided not to use. Paid $40 shipped, I was going to return them but the shipping is $20. Hoping to sell for $40 or B/O. I don’t have pictures of the actual item...