The Derploader
- Thread starter Preloader
- Start date
wingman
Active member
I want to make this one bad, but realistically can't. It sucks to hear that you may not be there again this summer. Major bummer. Start my new schedule NEXT week, four 14's instead of 5. And the best part is wed off. I plan on making at least a monthly appearance at the track, if not more often. Make us norcal peeps proud and best that 14.2!
theenico
New member
Just as I had assumed, my toe was in by over one degree on each side.
I'm zeroed now.
How was the camber?
Preloader
The M32 Martyr
I sent my log from my best run to Vince and I'm installing the Wacetrac on the MZ0 early next week. If he gives me an update by then, I may head back on Wednesday.
Oh yeah....... This is all possible because I just got laid off.
So I'll be working on the Preloader full time for now.
Oh yeah....... This is all possible because I just got laid off.
So I'll be working on the Preloader full time for now.
sx sonic
New member
I sent my log from my best run to Vince and I'm installing the Wacetrac on the MZ0 early next week. If he gives me an update by then, I may head back on Wednesday.
Oh yeah....... This is all possible because I just got laid off.
So I'll be working on the Preloader full time for now.
Wohooo, here comes derploader 2.0
Last edited:
Eric Smit
Enforcer
I don't think there is an appropriate picture for that meme. hahaha.
Preloader
The M32 Martyr
So here's the Version 2.0 list:
Wavetrac LSD
Electric cut-out right off the downpipe
Vermont Tuner Enlarged Compressor
Gasket Ported Exhaust mani
Rev limit bumped to 7k
The VT Compressor is ordered, but will be a couple weeks out. The cutout and Wavetrac should happen by next week.
Wavetrac LSD
Electric cut-out right off the downpipe
Vermont Tuner Enlarged Compressor
Gasket Ported Exhaust mani
Rev limit bumped to 7k
The VT Compressor is ordered, but will be a couple weeks out. The cutout and Wavetrac should happen by next week.
Eric Smit
Enforcer
sx sonic
New member
Vince I found a new trans for ya.
It's a manual, Its got a clutch, its got 15 forward gears and 4 reverse It takes NLS's all day, It's got a nuetral, It's even got Park.... oh and did i mention you only have to use the clutch when going between P,N,D, & R ranges!
It's a manual, Its got a clutch, its got 15 forward gears and 4 reverse It takes NLS's all day, It's got a nuetral, It's even got Park.... oh and did i mention you only have to use the clutch when going between P,N,D, & R ranges!
Last edited:
Preloader
The M32 Martyr
That must be a crawler or a scraper.
I've decided to stick with the MZ0. Wavetrac is going in it on Tuesday. Once I get my top end optimized to power up to 7k, the MZ0 should shine.
My next tune update will have rev limit at 7k. I'm bouncing off the limiter way too often even with my current set up. But the larger compressor will have me spending a lot more time up there.
I'm also looking at Hoosier Slicks for the 15's. I think Drag Radials could do worse damage to the drivetrain than slicks because radials have stiffer sidewalls, and that causes the hostile wheel hop.
I've decided to stick with the MZ0. Wavetrac is going in it on Tuesday. Once I get my top end optimized to power up to 7k, the MZ0 should shine.
My next tune update will have rev limit at 7k. I'm bouncing off the limiter way too often even with my current set up. But the larger compressor will have me spending a lot more time up there.
I'm also looking at Hoosier Slicks for the 15's. I think Drag Radials could do worse damage to the drivetrain than slicks because radials have stiffer sidewalls, and that causes the hostile wheel hop.
