Problem on 1.4T CEL P1101

C

cokegarcia

New member
I'm experiencing an annoying problem on my car. It's and Opel Corsa 1.4T, wich holds the same motor as the cruze, A14NEL. I'm getting the P1101 check engine light pretty much every two days. First i've read that's related to the MAF sensor being out of range (now i've been told it's air intake performance), so I bought a new Bosch MAF from eBay, cleared the code with OP-COM, no change, P1101 again in after 50-100 KM. I don't see any obvious difference on the performance of the car, either have any other code. Have been figthing with this for about 3 months. I live in Chile, so I don't really have access to many parts, since GM doesn't sell the turbo version of the CRUZE, SONIC here and not many people drive OPEL cars, so I want to know your opinions/experiencies before throwing expensive parts. I've checked the PCV disc next to the oil filler, no noise, either air sucktion. Should i try replacing the PCV hose?? What elso could that be??

Dealer is not really the first option here, since mechanics are not really experienced with these kind of motors and are really expensive on human hour worked, i've tryed and received crap like deleting the code only... Also the car is running on EDS re-map 165 HP, 260 NM, only use 97 octanes premium gas and change oil every 5K miles...

I've got a ELM327 reader, wich I connected yesterday to the ECU to check throttle, wich showed 12%, is that the same as "throttle position angle"? (P1101 set in Cruze or Sonic - iATN)

Any ideas, help on this??
 
R

rodslinger

Member
I didn't pay attention to the part about the IPF tune. If this were my car the first thing I would do is take the tune out and return it to stock to rule out any of the mods causing the issue.

Do you still have the handheld programmer that comes with the IPF tune or was it done at a local tuner?
 
S

Sneakerfix

New member
Did you ever clean your throttle body? Or did you clear the code after going back to the oem air box as I recommended you do on cruzetalk?

I had the same code when I ported my TB thought it was the MAF sensor. Your either getting to much air flow or to little airflow in to the engine.
 
C

cokegarcia

New member
Exactly, not sure if its too much or too little. Ill try to clear the TB on the weekend, any advise or guide?? Not even sure where it is, is it after mainfold that follows the air intake under the plate?? Havent ever cleaned it, im @ 30K miles.

Since i tryed with another MAF i think ot might be a dirty TB or a bad PCV (no whistle or sign tho, new design cam). Talking about TB, reading at idle seems normal @ 12%. I have noticed that code tends to comeback after a high RPM drive, sometimes just after a 5-6K rpm run and others next time I turn the car on after the run.

Thanks so much on your thoughts guys, pretty useful!!! ;)
 
Last edited:
C

cokegarcia

New member
Ive had the following photogram today, CEL P1101 came back three days after I desconected battery to try a relearn.

What could it be?? Air flow?? Came on after a drive I was almost parking.

Fuel Status = 0 byte
Carga de motor = 13.725 %
Temperatura del refrigerante del motor = 102 °C
Ajuste combustible a corto Banco 1 = -6.25 %
Consumo de combustible a largo banco 1 = -10.156 %
Presión de combustible = 0 psi
Presión del colector = 3.771 psi
RPM motor = 1,024.5 rpm
Velocidad (OBD) = 15 km/h
Avance temporal = 13 °
Temperatura de toma de aire = 28 °C
Caudal de aire = 1.89 g/s
Posición del acelerador (colector) = 25.098 %
Consumo combustible banco 1 sensor 1 = -6.25 %
Run time since engine start = 723 s
Nivel de combustible (De la ECU) = 81.569 %
Distance travelled since codes cleared = 339 km
Presión atmosférica (del vehículo) = 13.779 psi
Temperatura del catalizador (Banco 1,Sensor 1) = 573 °C
Voltaje (Módulo de control) = 13.421 V
Cargar del motor(Absoluta) = 13.725 %
Commanded Equivalence Ratio(lambda) = 1
Posición relativa del acelerador = 11.765 %
Temperatura de aire ambiente = 25 °C
Posición absoluta del acelerador B = 23.922 %
Posición del pedal del acelerador D = 20 %
Posición del pedal del acelerador E = 9.804 %

Fin del informe.
 
S

Sneakerfix

New member
That's some blow by oil. Loosen the clamps all the way and squeeze the center of the hose and twist hard from side to side
 
K

kevjam79

New member
Clean the MAF with MAF cleaner. Clean the TB with TB cleaner. Don't move the TB butterfly. Reinstall stock air box and factory filter. Insure all hoses are reinstalled correctly. Reset codes and unplug battery for 10 minutes or more. Drive.

Also, check your oil filler area. Is there any oil around the valve cover? It will look like misty oil fumes.


Sent from my iPhone using Tapatalk
 
C

cokegarcia

New member
kevjam79 said:
Clean the MAF with MAF cleaner. Clean the TB with TB cleaner. Don't move the TB butterfly. Reinstall stock air box and factory filter. Insure all hoses are reinstalled correctly. Reset codes and unplug battery for 10 minutes or more. Drive.

Also, check your oil filler area. Is there any oil around the valve cover? It will look like misty oil fumes.


Sent from my iPhone using Tapatalk
Click to expand...

There is not.

So i should clean the TB with spray only on the side that air comes in? I
Dont have a spare gasket that seals the other side.
 
K

kevjam79

New member
If you don't have gaskets, I would just spray from the outside.

How many miles do you have on it and how long did you run the aftermarket filters?


Sent from my iPhone using Tapatalk
 
C

cokegarcia

New member
kevjam79 said:
If you don't have gaskets, I would just spray from the outside.

How many miles do you have on it and how long did you run the aftermarket filters?


Sent from my iPhone using Tapatalk
Click to expand...

all miles about 32K, I used a K&N panel filter - and a Ramarir Conic w/o cover for about 20-25K.

Thanks,
 
You must log in or register to reply here.

Latest posts

Members online

Total: 72 (members: 3, guests: 69)

Share this page

Top